View B39941B4380P810_8974448.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

saw filters for automotive electronics series/type: b4380 the following products presented in this data sheet are being withdrawn. ordering code substitute product date of withdrawal deadline last orders last shipments B39941B4380P810 2016-01-08 2016-04-15 2016-07-15 for further information please contact your nearest epcos sales office, which will also support you in selecting a suitable substitute. the addresses of our worldwide sales network are presented at www.epcos.com/sales.
2 may 04, 2012 b4380 942.5 / 881.5 mhz please read cautions and warnings and important notes at the end of this document. saw components saw 2in1 filter data sheet application n low-loss 2in1 rf filter for mobile telephone gsm 900 and gsm 850 systems, receive path (rx) n usable passband: filter 1 (gsm 900): 35 mhz filter 2 (gsm 850): 25 mhz n unbalanced to balanced operation for all filters n impedance transformation from 50 w to 150 w for both filters n low amplitude ripple n suitable for gprs class 1 to 12 t.b.d features n package size 1.5 x1.1 x 0.40 mm 3 n package code qcs10w n rohs compatible n approx. weight 0.003 g. n package for s urface m ount t echnology ( smt ) n ni, gold-plated terminals n aec-q200 qualified component family (operable temperature range C40?c to +85?c) n e lectrostatic s ensitive d evice ( esd ) 0.18 0.175 0,39 bottom view 0.18 0.075 0.21 0.075 6 7 8 9 10 5 1234 side view 1.1 top view 0.49 0,4 1.5 pin configuration n 1 input [ filter 1] n 4 input [ filter 2 ] n 6,7 output balanced [ filter 2 ] n 8,9 output balanced [ filter 1 ] n 2,3,5,10 case ground 2 , 3 , 5 , 10 4 1 8 7 6 9
3 may 04, 2012 b4380 942.5 / 881.5 mhz saw components saw 2in1 filter data sheet please read cautions and warnings and important notes at the end of this document. characteristics of filter 1 ( gsm 900 ) temperature range for specification: t = -20 ?c to +75 ?c terminating source impedance: z s = 50 w terminating load impedance: z l = 150 w || 72 nh (balanced) min. typ. @25?c max. center frequency f c 942.5 mhz maximum insertion attenuation a max 925.0 ... 960.0 mhz 1.3 2.3 1) 1) 1.9 db at 25?c db amplitude ripple (p-p) da 925.0 ... 960.0 mhz 0.8 1.5 2) 2) 1.2 db at 25?c db vswr 925.0 ... 960.0 mhz 1.9 2.3 common mode rejection ratio 925.0 ... 960.0 mhz 19 25 db attenuation a 100.0 ... 480.0 mhz 45 55 db 480.0 ... 900.0 mhz 30 35 db 900.0 ... 905.0 mhz 27 31 db 905.0 ... 915.0 mhz 20 3) 3) 23 db at 25?c 30 db 980.0 ... 1000.0 mhz 25 29 db 1000.0 ... 1850.0 mhz 28 31 db 1850.0 ... 1920.0 mhz 40 44 db 1920.0 ... 3700.0 mhz 35 39 db 3700.0 ... 6000.0 mhz 30 36 db
4 may 04, 2012 b4380 942.5 / 881.5 mhz please read cautions and warnings and important notes at the end of this document. saw components saw 2in1 filter data sheet maximum ratings of filter 1 operable temperature range t C40/+85 ?c storage temperature range t stg C40/+85 ?c dc voltage v dc 0 v esd voltage v esd 100 1) 1) acc. to jesd22-a115a (machine model), 1 negative & 1 positive pulse. v machine model, 1 pulse input power at gsm 850, gsm 900 p in 15 dbm effective power in the on-state, gsm 1800, gsm 1900 p in 15 dbm duty cycle 4:8 tx bands
5 may 04, 2012 b4380 942.5 / 881.5 mhz saw components saw 2in1 filter data sheet please read cautions and warnings and important notes at the end of this document. transfer function of filter 1 transfer function of filter 1 - wideband
6 may 04, 2012 b4380 942.5 / 881.5 mhz please read cautions and warnings and important notes at the end of this document. saw components saw 2in1 filter data sheet characteristics of filter 2 ( gsm 850 ) temperature range for specification: t = -20 ?c to +75 ?c terminating source impedance: z s =50 w terminating load impedance: z l = 150 w || 82 nh (balanced) min. typ. @25?c max. center frequency f c 881.5 mhz maximum insertion attenuation a max 869.0 ... 894.0 mhz 1.4 2.2 1) 1) 1.9 db at 25?c db amplitude ripple (p-p) da 869.0 ... 894.0 mhz 0.7 1.4 2) 2) 1.1 db at 25?c db vswr 869.0 ... 894.0 mhz 1.7 2.2 commom mode rejection ratio 869.0 ... 894.0 mhz 17 20 db attenuation a 100.0 ... 447.0 mhz 45 48 db 447.0 ... 849.0 mhz 30 34 db 914.0 ... 954.0 mhz 21 25 db 954.0 ... 1738.0 mhz 28 33 db 1738.0 ... 1788.0 mhz 40 55 db 1788.0 ... 3476.0 mhz 35 40 db 3476.0 ... 6000.0 mhz 26 31 db
7 may 04, 2012 b4380 942.5 / 881.5 mhz saw components saw 2in1 filter data sheet please read cautions and warnings and important notes at the end of this document. maximum ratings of filter 2 operable temperature range t C40/+85 ?c storage temperature range t stg C40/+85 ?c dc voltage v dc 0 v esd voltage v esd 100 1) 1) acc. to jesd22-a115a (machine model), 1 negative & 1 positive pulse. v machine model, 1 pulse input power at gsm 850, gsm 900 p in 15 dbm effective power in the on-state, gsm 1800, gsm 1900 p in 15 dbm duty cycle 4:8
8 may 04, 2012 b4380 942.5 / 881.5 mhz please read cautions and warnings and important notes at the end of this document. saw components saw 2in1 filter data sheet transfer function of filter 2 transfer function of filter 2 - wideband
9 may 04, 2012 b4380 942.5 / 881.5 mhz saw components saw 2in1 filter data sheet please read cautions and warnings and important notes at the end of this document. esd protection of saw filters saw filters are e lectro s tatic d ischarge sensitive devices. to reduce the probability of damages caused by esd, special matching topologies have to be applied. in general, esd matching has to be ensured at that filter port, where electrostatic discharge is expected. electrostatic discharges predominantly appear at the antenna input of rf receivers. therefore only the input matching of the saw filter has to be designed to short circuit or to block the esd pulse. below three figures show recommended esd matching topologies. for wideband filters the high-pass esd matching structure needs to be at least of 3 rd order to ensure a proper matching for any impedance value of antenna and saw filter input. the required component values have to be determined from case to case. fig. 1 mlc varistor plus esd matching fig. 2 suppressor diode plus esd matching in cases where minor esd occur, following simplified esd matching topologies can be used alternatively. fig. 3 3 rd order high-pass structure for basic esd protection in all three figures the shunt inductor lp2 could be replaced by a shorted microstrip with proper length and width. if this configuration is possible depends on the operating frequency and available pcb space. effectiveness of the applied esd protection has to be checked according to relevant industry standards or customer specific requirements for further information, please refer to epcos application report: esd protection for saw filters . this report can be found under www.epcos.com/rke.click on applications notes. mlc1 cs1 lp2 cs3 to output matching dp1 lp2 cs3 cs1 to output matching lp2 cs3 cs1 to output matching
10 may 04, 2012 b4380 942.5 / 881.5 mhz please read cautions and warnings and important notes at the end of this document. saw components saw 2in1 filter data sheet references type b4380 ordering code B39941B4380P810 marking and package c61157-a8-a10 packaging f61074-v8227-z000 date code l_1126 s-parameters b4380_lb_nb.s3p, b4380_lb_wb.s3p b4380_ub_nb.s3p, b4380_ub_wb.s3p see file header for port/pin assignment table. soldering profile s_6001 rohs compatible defined as compatible with the following documents: "directive 2002/95/ec of the european parliament and of the council of 27 january 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. 2005/618/ec from april 18th, 2005, amending directive 2002/95/ec of the european parliament and of the council for the purposes of establishing the maxi- mum concentration values for certain hazardous substances in electrical and electronic equipment." moldability before using in overmolding environment, please contact your epcos sales office. matching coils see inductor pdf-catalog http:// www .tdk.co.jp/tefe02/coil.htm#aname1 and data library for circuit simulation http://www.tdk.co.jp/etvcl/index.htm for further information please contact your local epcos sales office or visit our webpage at w ww.epcos.com . published by epcos ag systems, acoustics, waves business group p.o. box 80 17 09, 81617 munich, germany ? epcos ag 2012. this brochure replaces the previous edition. for questions on technology, prices and delivery please contact the sales offices of epcos ag or t he international representatives. due to technical requirements components may contain dangerous substances. for information on t he type in question please also contact one of our sales offices.
11 may 04, 2012 important notes t he following applies to all products named in this publication: 1. some parts of this publication contain statements about the suitability of our products for certain areas of application . these statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. we nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. as a rule, epcos is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. for these reasons, it is always ultimately incumbent on the customer to check and decide whether an epcos product with the properties described in the product speci?cation is suitable for use in a particular customer application. 2. we also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as speci?ed. in customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. the warnings, cautions and product-speci?c notes must be observed. 4. in order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous) . useful information on this will be found in our material data sheets on the internet (www.epcos.com/material). should you have any more detailed questions, please contact our sales of?ces. 5. we constantly strive to improve our products. consequently, the products described in this publication may change from time to time . the same is true of the corresponding product speci?cations. please check therefore to what extent product descriptions and speci?cations contained in this publication are still applicable before or when you place an order. we also reserve the right to discontinue production and delivery of products . conse- quently, we cannot guarantee that all products named in this publication will always be available. the aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-speci?c products. 6. unless otherwise agreed in individual contracts, all orders are subject to the current version of the general terms of delivery for products and services in the electrical industry published by the german electrical and electronics industry association (zvei) . 7. the trade names epcos, baoke, alu-x, ceradiode, ceralink, csmp, cssp, ctvs, deltacap, digisimic, dssp, filtercap, formfit, miniblue, minicell, mkd, mkk, mlsc, motorcap, pcc, phasecap, phasecube, phasemod, phicap, siferrit, sifi, sikorel, silvercap, simdad, simic, simid, sineformer, siov, sip5d, sip5k, thermofuse, windcap are trademarks registered or pending in europe and in other countries. further information will be found on the internet at www.epcos.com/trademarks.

▲Up To Search▲

Price & Availability of B39941B4380P810

	To Download B39941B4380P810 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .